Fog Light Installation: How To Install Foglights

car fog light installation

Choosing the right light for your car can be a little bit tricky. Not every light is good for use in the car. Fog lights come in handy when you’re driving in poor lighting conditions like rain, fog, pitch darkness, or even snow. Responsible drivers and car owners find this incredible light useful and so they would love to mount it on the car. Fog light provides ample light that travels far and covers the road surfaces quite clearly. 

To install fog lights on your car you can Park and Turn off the Engine, Disconnect the Battery Terminals, Disconnect Battery Terminals, Access the Location To Install, Wire in Fog Lights, Take off the Fender, and Connect Positive lead. This allows motorists to see potholes and other dangers on the road much clearly; thus, they can avoid blown-out tires and several other issues. If you have searched endlessly for the best guide on how to install fog light, this article is for you. You will learn everything in detail about fog lights and the steps to install them. 

Read through this article to find out why you need a fog light and how to install fog lights.

What is Car Fog Light?

Fog lights are a kind of headlights that are structured to emit light in a bar-shaped beam. This beam is structured with a cutoff are the top, and the lights are installed close to the ground so that the lights are aimed towards the ground sharply. 

These low beam headlights are aimed towards the grounds so they can illuminate the ground at a long distance. However, it is important to note that fog lights only provide illumination on the ground in front of them.

Why Do You Need a Fog Light On Your Car?

Fog lights are needed in your car because they provide illumination to the dark sides of the road that headlights cannot reach; it is ideal in poor visibility conditions. Since it is mounted close to the ground, it causes less glare and yet provides more illumination on the road, unlike headlights.

Headlights are not ideal when driving in snow or the fog because they reflect light on the snow and fog and therefore create glare on the driver’s face. The wider swath of light provided by the fog light helps to ensure much safer driving by assisting motorists in detecting potholes and wildlife early enough so as not to run into issues on the road.

Apart from its safety features that makes it important, it is also an amazing choice when you’re looking to add style to your vehicle. If you go for factory opened fog lights, you’ll get a variety of designs to choose from to fit your preferred style.

car fog light installation

How To Install Fog Light in Your Car?

Fog lights are great for improving visibility when you’re driving in terrible weather conditions; installation of fog lights is easy, and below is exactly how to go about it. To get started, you will require a screwdriver, plier, electrical tap, wrench, extension, ratchet, diagonal cutters, and probably a drill. Once you have these tools handy, then you can start with the installation process.

Step 1: Park and Turn Off Engine

First, there is a need to park the car on a level surface and turn off the engine. Once you carry this out, open before installing the fog lights; keep the screw and nuts in a safe place, so you don’t lose them.

Step 2: Disconnect Battery Terminals  

Find the battery and remove the negative terminal, fix the wiring into the layout however you want, and avoid places that might get in your way. If you check the steering wheel, you’ll notice an interior panel. Remove the fuse access panel carefully; make sure you handle it delicately so as not to damage it. There is a panel below the steering column that you’ll need to remove.

Step 3: Access the Location of To Install

Once you do this, you can find the right spot to fix in the switch; ensure it is a location you can easily access. Get to the ground and search for ground wires; you should easily find a bold that you can fasten through metal. Remove the bolt and slide the ground connector. After, this you can retighten the bolt to its previous setting.

Locate an empty 12V fuse by making use of the voltmeter while the engine is on. When you find the fuse, connect the positive connector. Make sure that the fog light only goes on when the engine is on and goes off when the engine is off.

Step 4: Wire in Fog Lights

To wire in the fog lights, pass the wiring through the firewalls and use a coat hanger if you find the firewall a bit stiff. This is where the connection of the switch to the engine bay wiring takes place. When there is extra wiring, bundle it up and put it in the interior panel to ensure it is completely out of the way. The next step is to create a connection to the fog light or the location where you will place the fog lights.

Step 5: Take Off the Fender

Look out for any open space behind the headlights and take off the fender so it would be easier for you to access from the opposite side. With it removed, you can easily access the ideal position for the fog lights installation. Use a plastic trim removal tool to effectively remove the plastic cover if it doesn’t simply come off and connects the wires to each side.

Step 6: Connect Positive lead

Connect the positive lead carefully to the positive battery terminal and connect fog lights appropriately to the wiring. Carry out a test check to ensure everything is as it should be and is working perfectly. If it is, you can connect the battery terminal back, re-bolt everything, and arrange it back as it was.

Final Thoughts

Installing fog lights is a simple process, as you can see, and you can easily carry it out on your car to ensure that you see adequately in extreme weather conditions. You can either try this out yourself or get an expert mechanic to install them for you; I hope you enjoy your new fog lights. Fog Lights can sometimes come in various types; you may see fog lights under oxidized headlights as well.